Описание настроек BIOS Setup V1.3

Описание ошибок
GateA20 Error!
Address Line Short!
BIOS ROM checksum error System halted
Cache Memory Bad Do Not Enable Cache!
CH2 Timer Error
CMOS battery failed CMOS Battery Has Failed CMOS Battery State Low

CMOS Checksum Error CMOS Checksum Failure
CMOS Memory Size Mismatch
CMOS System Options Not Set
CMOS Time and Date Not Set
Disk Boot Failure Insert System Disk And Press Enter
Diskette Boot Failure
Diskette Drives Or Types Mismatch Error Run Setup
Display Switch Is Set Incorrectly Display Switch Not Proper
CPU External Cache
PCI 2 1 Support

PCI 2 1 Compliance
ISA 16bit I/O Wait States
ISA 16bit Mem Wait States
System Boot Up CPU Speed
BootSector Virus Detection
DRAM Burst at 4 Refresh
System Boot Sequence
System Boot Up Numlock Status
Pentium II Microcode
CPU MicroCode Updation

CPU Level 2 ECC Checking
CPU L2 Cache ECC Checking
CPU Level 1 Cache
CPU Level 2 Cache
CPU Level 2 Cache ECC Check
Data Integrity (PAR/ECC)
DRAM Page Mode
DRAM Paging
DRAM Paging Mode
SDRAM Page Control

CPU to DRAM Page Mode
CPUtoPCI Buffer
Latency for CPU to PCI write
CPUtoPCI 6 DW FIFO
CPUtoPCI IDE Posting
CPUtoPCI Read Buffer
CPUtoPCI Write Buffer
CPUtoPCI Write Latency
Quick Boot
Quick Power On Self Test

Hard Disk PreDelay
Delay For HDD (Secs)
PCI Delayed Transaction
Delayed Transaction Optimization
Delayed Transaction Timer
Daylight Saving
Delay IDE Initial
Delayed Transaction
Deturbo Mode
DMA n Assigned to

Resume On LAN
Virus Protection
BootSector Virus Protection
Virus Warning
Wait for F1 If Any Error
Wake On LAN
Weitek Coprocessor
X RxD TxD Active
Keyboard Controller Clock
KBC Input Clock Select

Doze Mode
Doze Speed
X KB Power On Password
DRAM Data Integrity Mode
DRAM ECC/PARITY Select
DRAM Idle Timer
Paging Delay
X KB Power On Hot Key

RAS# Precharge Time

RAS# Precharge Time
RAS# Precharge Period
FPM DRAM RAS# Precharge
FPM RAS Precharge
RAS# Precharge
EDO RAS Precharge
EDO RAS# Precharge Time
EDO RAS Precharge Timing
FPM/EDO RAS# Precharge Time
SDRAM RAS Precharge Time

SDRAM RAS# Precharge
Refresh Cycle Time
DRAM Refresh Cycle Time
Memory Refresh Rate
DRAM Refresh Rate
DRAM Refresh Period
Drive NA before BRDY
X IR Transmission Delay
NA# Pin Assertion
NA# Enable

Numeric Processor Test
Primary Display
Video
Bit I/O Recovery Time
Bit I/O Recovery Time
Automatic Power Up
Chassis Fan Speed
Fast RAS# to CAS# Delay
CPU Fan Speed
CPU Temperature

DRAM RAS to CAS Delay
DRAM Read Burst Timing
DRAM R/W Leadoff Timing
Error Halt
Halt On
ECP DMA Select
Parallel Port Mode
RAM Area
Enable Master
Extended Refresh

Extended ROM RAM Area
Fast Gate A20 Option
LOWA20# Select
Init Display First
Graphics Adaptor
VGA BIOS Sequence
IR Transfer Mode
UR2 Duplex Mode
UART 1/2 Duplex Mode
Duplex Select

InfraRed Duplex Type
IR Function Duplex
Assign IRQ For VGA
ISA Clock Select Enable
ISA MEM Block Size
Floppy Disk Access Control (R/W)
Gate A20 Option
Graphics (AGP) Aperture Size
HDD Power Down
HDD S M A R T Capability

HiSpeed Refresh
Hidden Refresh
Onboard AHA BIOS
Onboard PCI IDE Enable
OS/2 Onboard Memory >MB
PCI Passive Release
Arbitration Priority
PCI Arbiter Mode
PCI Arbitration Mode
PCI Arbit Rotate Priority

DMA/ISA Master Before PCI
PCI Bus Timeout
PCI Master Latency
Latency Timer
PCI Clocks
PCI Initial Latency Timer
PCI Preemption Timer
Video Palette Snoop
Multimedia Mode
PCI Concurrency

Bus Concurrency
Passive Release
Password Checking
PCI Bus Arbitration
PCI Bus Parking
PCI Clock Frequency
PCI Dynamic Decoding
PCI IDE IRQ Map to
PCI IRQ Activated by
Power Button Function

Video BIOS Area Cacheable

Video BIOS Area Cacheable
Video Off After
Preempt PCI Master Option
Processor Number Feature
Resources Controlled By
PS/2 Mouse Function Control
PWR Button less then 4 Secs
PWR Lost Resume State

PWRON After PWRFail
Ref/Act Command Delay
Refresh During PCI Cycles
Refresh RAS# Assertion
Report No FDD For WIN 95
Reset Configuration Data
Resume by Ring
RTC Alarm Resume (From Soft)
RTC Y2K H/W Roll Over
SDRAM Banks Close Policy

SDRAM CAS# Latency
SDRAM CAS to RAS Delay
SDRAM Configuration
Single ALE Enable
Slow Refresh
Snoop Ahead
Speculative Leadoff
Spread Spectrum Modulated
Standby Mode

Stby Speed
Stop CPU at PCI Master
Suspend Switch
Swap Floppy Drive
SYMBIOS (NCR) SCSI BIOS
System Thermal
Trigger Method
TurnAround Insertion
Keyboard Reset Control
Typematic Rate Delay

UART2 Mode Select

Обзор команд и драйверов MS-DOS 6.2

Команда MOVE
Перемещает один или более файлов в новое место. Используется также для переименования каталогов.
MOVE [/Y /-Y][диск:][маршрут]имя_файла[,[диск:][маршрут] имя_файла[...]] приемник
Параметр [диск:][маршрут]имя_файла задает расположение и имя перемещаемого файла или файлов. "Приемник" задает новое расположение файла или новое имя каталога и может содержать буквенную метку диска и двоеточие, имя каталога или их комбинацию. Если перемещается только один файл, вы можете задать также имя файла (если хотите его переименовать).

Команда MOVE
Команда DATE
Команда LASTDRIVE

Содержание раздела

---

---